Natural colourants can be compounded into polylactic acid (PLA) and polybutylene succinate (PBS) on conventional twin-screw extrusion and injection moulding equipment, with only modest changes in melt flow and mechanical behaviour, according to a study on natural pigment-based colour masterbatches. The limiting factor is not processing but light: after 50 hours of xenon-lamp exposure, most formulations shifted by more than ΔE* = 2, a difference generally visible to the eye.
The work, titled Sustainability in the Development of Natural Pigment-Based Colour Masterbatches and Their Application in Biopolymers, examined four commercial natural pigments: blue spirulina, yellow curcumin, red beetroot and green chlorophyllin. Each was combined with PLA and PBS to produce colour masterbatches by twin-screw extrusion, then diluted into the matching polymer matrix at 2, 4 and 6 wt% and injection moulded into test specimens. The masterbatch formulation also contained titanium dioxide, calcium carbonate and stearic acid, included to support UV protection, dispersion and processing.
Thermal limits define the processing window
Natural pigments are organic structures that can begin to degrade at temperatures below those needed to melt the carrier polymers. Thermogravimetric analysis put degradation onset at approximately 229 °C for spirulina, 244 °C for curcumin, 258 °C for chlorophyllin and 267 °C for beetroot, while PLA and PBS degrade at considerably higher temperatures.
The researchers therefore selected extrusion profiles that melted each polymer while limiting thermal exposure of the pigments: 145 °C for PBS and 190 °C for PLA, with the twin-screw extruder running at 65 rpm and a feed rate of 2 kg/h.
Spirulina loses colour in PLA
That window suited most pigment–polymer pairs, with one clear exception. During PLA processing, spirulina lost its characteristic blue colour, so no blue PLA masterbatch could be produced. PBS, processed at the lower temperature, preserved enough pigment stability for successful compounding. The outcome indicates that pigment compatibility depends strongly on the thermal processing requirements of the specific matrix, rather than on the colorant alone.
Melt flow and mechanical performance stay near baseline
The natural pigments caused only limited changes in the rheological behaviour of the matrix. Melt flow rate decreased slightly after pigment incorporation, indicating a modest increase in melt viscosity. Neat PLA measured about 50 g/10 min, and the corresponding natural-pigment masterbatches stayed close to that value; PBS showed a similar, small reduction.
For compounders, that result matters: a natural colour system offers little practical value if it forces major changes to screw design, pressure settings or moulding conditions. In this study, conventional twin-screw compounding and injection moulding handled most formulations without major processing problems.
Tensile and impact testing across the 2 to 6 wt% addition range showed no significant losses in overall mechanical performance. PLA started from a Young's modulus of about 1710 MPa and tensile strength of 65.6 MPa, PBS from about 392 MPa and 34.5 MPa; the coloured formulations remained close to those baselines. Impact strength also stayed within a similar range, although individual pigments produced some variation.
Photostability is the remaining barrier
Successful extrusion did not ensure durable colour. The exception to the general fading trend was the PLA formulation containing 2 wt% green chlorophyllin masterbatch, which showed the highest photostability. The study points to UV stability as the largest barrier to broader use, noting that packaging, consumer products, agricultural parts and outdoor applications may require additional stabilisation, protective coatings or pigment modification before natural colours can compete with conventional systems over long service periods.
Natural pigment masterbatches still need further development, particularly in lightfastness and thermal stability. The authors add that future work should focus on improving colour stability during processing and during subsequent service exposure.
Lower carbon footprint
The environmental comparison favoured the natural colorants. Under the study's assumptions, one kilogram of curcumin pigment generated about 0.04 kg CO2-eq, compared with 18.65 kg CO2-eq for the inorganic green reference pigment. The natural-pigment masterbatches also consumed less electricity during extrusion and pelletising.
