Custom Manufacturing

Britain's Additive Manufacturing Strength Stops Short of the Factory Floor

Ahead of Formnext 2026, UK founders and researchers describe a sector rich in invention but thin on installed equipment, repeat orders and domestic demand.

Ines FarkasNovember 16, 20265 min read2 views
A wooden pulley block and a metal additively manufactured part sit side by side on a workshop bench, with a large-format printing cell visible behind them.

Britain will be the partner country at Formnext 2026 in Frankfurt from 17 to 20 November, and the case for its additive manufacturing sector rests on a long record of invention. The harder question, raised repeatedly by the founders and researchers interviewed for this UK series, is who ends up making the parts.

Craig Pyser, chief executive of Portsmouth-based AMufacture and chair of Additive Manufacturing UK (AMUK), frames the historical complaint plainly: British engineers invent things that others prove more adept at selling. His own answer is commercial rather than patriotic. A customer needs a reason to manufacture here, and for some buyers the ability to visit the factory, establish where a part came from and get a replacement quickly already provides one.

A customer who knew what it used

The Portsmouth dockyard supplies the standard example. During the Napoleonic Wars the Royal Navy was buying about 100,000 wooden pulley blocks a year, and a single ship, HMS Victory, needed more than a thousand. In 1803 the first set of block-making machines designed by Marc Isambard Brunel and built by Henry Maudslay went into operation; by 1808, 45 machines were producing 130,000 blocks. The engineering gets the credit, but the Admiralty's contribution mattered too: it knew what it used, in which sizes and in what quantities, and could watch a first installation work before committing to the next.

That sequence, a customer with a defined requirement followed by a trial and then a repeat order, is the one British machine builders still describe as decisive.

Invention is not the constraint

The evidence of British invention is not in doubt. The European Patent Office counted 1,925 international patent families in additive manufacturing originating in the UK between 2001 and 2020, close to France's 1,938. AMUK's 2026 annual plan puts the UK market at £515m to £740m in 2024, or 3% to 4.3% of the global total, a range that reflects disagreement between market estimates. Neither figure says much about how much production happens in Britain: a patent family records an attempt to protect an invention, and a market estimate can include machines bought from overseas.

Will Richardson, chief executive of Wayland Additive, points to metallurgy and materials science at Sheffield, Birmingham, Cambridge and Oxford and to the Henry Royce Institute. In October a Calibur3 metal system left the company's Huddersfield facility for the University of Innsbruck, where researchers will investigate difficult-to-process materials, including those intended for high temperatures. Britain built and exported the machine; some of the knowledge of what it can do will now accumulate in Austria.

Other routes exist. Alloyed, which began in Oxford materials research, licensed a cast nickel alloy to Hitachi Metals in 2018, later opened component development and production in Abingdon and Seattle, and sold its first flight parts from Seattle in 2023. One research base, three quite different businesses.

When a project ends, a company still has to sell

Jake Hand, co-founder of Exeter-based Rapid Fusion, says the business is profitable without R&D funding, but credits Innovate UK support with letting it develop its own technology and share costs it would otherwise carry alone. His criticism concerns the moment a project succeeds: in his words, "they back a project, but not a business." A completed award can leave a working machine and evidence sufficient for the funder, while the customer still asks whether it can make a particular mould, who will train the operator and what happens if the machine stops mid-job. Answering those questions for a single sale can absorb months of a small company's time.

Sometimes a graduate supplies the bridge. At Kingston University, a former student named Raghav joined Rapid Fusion and insisted his employer and his old department meet, according to operations manager Lesley Stigling. The result was a £450,000 Zeus robotic cell at the Roehampton Vale campus that combines large-format printing with CNC milling: equipment the university can use in-house, offer to industrial partners and teach on, and a reference installation for the manufacturer.

Equity and the first outside investor

John Robinson, additive manufacturing research commercialisation manager at the University of Wolverhampton, incorporated a company in May 2017 that funded his PhD, and says he and the university filed several patent applications together in 2024. His current work includes using more than one material in devices that carry heat away from data-centre equipment. He recalls the university's former technology transfer office wanting 75% of the company; more recent discussions with its enterprise team have been about a 10% stake. Both were proposals, but the difference is large before any outside money arrives.

The direction of travel is national. The Royal Academy of Engineering and Dealroom found that among UK deep-tech hardware spin-outs in their sample, the average non-cash stake taken by universities fell from 25% in 2015–19 to 14% in 2024–25, on partial 2025 data. Louis Masters of Hydra Manufacturing, a University of Leeds spin-out developing equipment for technical ceramics, announced £320,000 in equity investment led by SFC Capital in March, about £577,000 including earlier grant support, and was considering raising £1m or more. He knows an investor may want two more installations, and that winning those customers competes for the same time as raising the money.

Where the customers are

Jason Bowes, chief operating officer of CloudNC, told a Manufacturing Technologies Association briefing at the House of Lords on 12 November that it is "far, far easier to sell our technology in the U.S. than it is here." His company develops AI-assisted software for programming CNC machines and tests it in its own British factory. A cautious purchasing manager, meanwhile, may understand the economics perfectly: a process that lowers cost per part at full utilisation offers little comfort to a shop that can fill only a fraction of its hours.

AMufacture shows what a production-led order book looks like. Pyser estimates 95% to 98% of its work is now production, with defence its largest sector over the past year alongside marine and automotive; some defence customers revise designs every six to eight weeks, so a local supplier able to take a revised file and deliver the next batch can win repeat orders while the product keeps changing. When one customer took some production in-house, AMufacture helped it get the printer running, and two years later bought the machine back, software, staff and post-processing having made the in-house operation dearer than expected.

Richardson of Wayland locates part of the problem in the installed base: "if you're not actually doing the doing, then you're not going to get good at it." With few factories running a given process, each employer must train people who elsewhere would arrive already experienced. Renishaw's Ben Deary and Ed Littlewood describe the same effect when production returns after years of buying overseas: a machine can be commissioned and operators hired only to find that a once-reliable supplier of a component or service has disappeared.

Qualification is the other cost. Jason Hutt, managing director of Fastech, notes that "casting's approved, isn't it?" The customer already buys to an agreed specification, while an additively manufactured replacement may need evidence specific to the equipment, process and grade, and a second buyer may ask for much of the work again. The £38m Airbus-led DECSAM programme, with Renishaw, GKN Aerospace, Apex, the Manufacturing Technology Centre and others, is one attempt to share that burden in civil aerospace, with ground and flight demonstrators and qualification guidance planned.

What public procurement can buy

James Selka, chief executive of the Manufacturing Technologies Association, told the Lords briefing that investment was poised to enter British manufacturing but needed "a proper demand signal and co-investment from government," putting energy prices first among immediate obstacles. Lord Harrington of Watford, chair of Make UK, recalled that sector deals under Theresa May worked where companies could match public money, and knew the financing gap from the other side: GeoPura, the hydrogen power business he chaired, ended up being sold to Canada's Ballard Power Systems for £275m upfront, completed in August.

Procurement is the lever government holds directly, as Harrington acknowledged when asked about fusion. In 2025 the UK Atomic Energy Authority commissioned two additive systems at its Central Support Facility, a Freemelt electron-beam machine for tungsten work and a Nikon SLM laser system supplied by Kingsbury Machine Tools with support from Additure, and reports that British participants including Laser Additive Solutions, The Welding Institute and WAAM3D contributed to fusion maintenance projects. UKAEA publishes a quarterly procurement pipeline distinguishing possibilities, pre-commercial work and confirmed requirements. For a supplier deciding whether to hire or invest, that distinction is worth more than a general undertaking to support British industry.

Pyser has a simpler test for Frankfurt. An overseas company choosing Britain as its European base would count. So would an answer, a year from now, to who the exhibitors' next customer was, the question the Admiralty settled in May 1803 when it ordered Brunel's machines for smaller blocks.